工程案例
您当前的位置:主页 > 工程案例 >

圆柱模板车间

施工方案

1、三米以上模板要错位安装。安装圆模板时,当柱高超过三米,模板的上下连接处的两块模板需要错开安装,错位安装可以保证圆柱体的垂直性和整体性。

2、固定钢带要求水平捆扎。水平扎捆可以保证钢带受力均匀,固定钢带的上下边距为22cm。(安装技巧:钢带安装时最好用钢尺对模板进行测量,在模板的同一高度四周钉上3-4个小钉子。上钢带时把钢带放在钉子上,即可保持钢带的安装水平)。安装螺丝时,每一个螺丝拧紧度要保持一致,这样才能保证钢带松紧度的一致性及施工安全(安装提示:最好同一棵柱子用同一个人加固螺丝)。圆模板合拢加固后,模板的底部圆平面最好离地面0.5-1cm距离,并用混凝土填缝。

3、模板上下接口位置加固。由于圆模板是错开安装,在上下模板水平接口的位置一定要用钢带进行加固,钢带要水平覆盖在接口部位,而且保证接口位置在加固钢带的中间,这样可以增强模板的稳固和施工的效果。

4、对模板进行保护。钢带安装好以后为了对模板进行保护,要在模板四周垂直加5*10cm的木方四个,并在用四个钢管固定木方,上下每层钢管的间距保持100cm最佳,这样不仅可以对木模板进行保护,而且可以缓冲振动棒的压力,使打出来的混凝土效果更好,同时这样保护也有利于对圆模板进行垂直定位,使模板的受力形成一个整体,达到二次加固的作用。

5、对模板进行混凝土浇注。圆模板浇灌混凝土小直径的七米高度以内可以一次性浇灌,七米以上高度建议分两次浇灌,大直径的建议3米进行一次浇注,第一次浇灌后120分钟即可进行第二次浇灌。

6、拆模流程。拆模时,依次把加固在圆模板外面的钢管、木方、钢带去除,此时模板自然脱模张开,如有个别没有自然张开的模板,只需要在凸凹槽接口位置用木条敲击震动一下,模板便可自然脱模(请严禁用工具撬开)。

郑重声明: 施工方在操作过程中要严格按照我公司提供的安装方法进行施工,如因我方产品质量原因造成的损失我方承担相关责任,如因安装不当造成的损失我方不承担相关责任。

 

 

圆柱木模板

 

 

圆柱模板厂家

 


 

 

construction plan

1, more than three meters to install the template dislocation. Install the circular template, when the column is over three meters high, the upper and lower two template template connections need to stagger installation, installation can ensure the vertical dislocation and a whole cylinder.

2, fixed steel belt level requirements. The level of binding strip can ensure the uniform stress, fixed on the bottom margin of 22cm steel. (Installation Tips: strip when installed using the ruler to measure, the template template pin in the same height around 3-4 small nails. With the steel on steel nails, you can keep the installation level strip). When installing screws, each screw tightening degree should be consistent, so as to ensure the consistency of the tightness of the steel belt and construction safety (Installation Tips: it is best to use the same column with the same reinforcement screws). The circular template closure after reinforcement, the bottom circular planar template best 0.5-1cm from the ground distance, and concrete filling.

3, the template upper and lower interface position reinforcement. Because we are staggered round plate installation, in the upper and lower level interface template must be reinforced with steel strip position, to strip horizontal coverage on the interface area, and ensure the position of the interface in the middle reinforcement of steel strip, which can enhance the stability and the effect of template construction.

4, to protect the template. The strip after installation in order to protect the template in the template to the vertical 5*10cm wood around four, and in four steel pipe fixing wood, the vertical distance of each layer of steel 100cm best, it can not only protect the wooden template, and can buffer the vibration rod pressure, make better concrete the effect of playing out, and it is also conducive to the protection of the vertical positioning of the circular template, forming a whole force of the template, reached two times the effect of reinforcement.

5, the template for concrete pouring. Within the circle template pouring concrete in small diameter height of seven meters to seven meters above the height of one-time irrigation, suggest two times of irrigation, large diameter of 3 meters for suggestions of pouring a first, 120 minutes after watering second times of irrigation.

6, the removal process. Chaimo, in turn, to reinforce steel circle template outside wood, steel template removal, the natural release open, if the individual has no natural open template, only on the convex and concave interface position with wooden percussion vibration, template can be natural release (please prohibit the use of tools to open).

Solemnly declare: to carry out construction in strict accordance with the construction method of installation provided by our company in the operation process, such as caused by the quality of our products cause loss of our responsibility, as a result of the loss caused by improper installation shall not be responsible.

质量是需要全员参与监督才能生产出顾客满意的产品
友情链接